3d Printed glove remover

The 3D printed Glove Remover PPE performance (personal protection equipment) safety product helps reduce the spread of infection while changing protective rubber gloves while promoting efficiency and convenience.

3d Printed glove remover

The idea for the glove remover was conceived for the coronavirus pandemic. Recommendations for additional improvement of the glove remover are welcome to share the story with anyone you think would benefit. 

We would appreciate it. Likewise, we are happy to receive feedback from environmental services officials or medical offices which might want to try one of our glove removers.

This device is essential for clinical staff or persons in the beauty care industry or the food industry. Also, a tattoo artist can use the glove remover to dispose of gloves.

Save time. Save money. Save your health.

Users must not tear or split their gloves while removing them. Studies have indicated that this can happen if the glove remover isn’t used correctly.

atol glove removal

Who Can Use The 3D Printed Glove Remover

Physicians, healthcare workers, food industry employees, and salon professionals wear protective gloves. However, the risk of contamination remains high when workers are forced to remove their gloves manually. Simply removing a protective glove can spread diseases from one person to the next.

The glove remover reduces this risk by cutting off the outer section of a glove at the wrist with a small blade. The glove remover also prevents the wearer from touching the outside of the glove and possibly spreading bacteria that could cause infections. The glove remover greatly reduces the risk of spreading diseases in places where people come in close contacts, such as healthcare facilities.

Every individual wears protective gloves and needs to dispose of them frequently. Workers are exposed to contracting contagious diseases when protective gloves are removed incorrectly.

When people do not change their gloves often or properly, they risk spreading infections among patients. Healthcare workers who wear protective gloves daily expose themselves to a greater risk of contracting diseases such as HIV, influenza, tuberculosis, and infections such as strep and staph.

 Glove remover decreases the danger of contamination. Contaminated disposable gloves take up space and must be disposed of at great cost. This contributes to increased waste disposal costs for healthcare facilities and businesses.

 

Glove remover is versatile; it can be mounted to walls, pipes, or tubes.

Instructions to mount the glove remover:

Mount the glove remover in a position where its tip is 60 and 80 cm (24-31 inches) over the waste container on the floor. I am using a low-profile waste container underneath.

Wall mounting:

Wall mounting: Insa the wall mounting plate (two teeth) with two screws vertically, one over the other on an appropriate divider. 

Supplement the glove remover into the wall mounting plate and screw it on. Use two screws for plastics on each side.

Pipe mounting:

Utilize a measurement of 2.5 cm (1 inch). For littler channels, wrap tape over a width of 6 cm (2.5 inches) around the funnel until a sufficient breadth is reached. 

Cinch the glove remover to the pipe utilizing the channel mounting plate (4 semi-round). Use four screws specifically for plastics and screw them into the funnel mounting plate from behind—the world’s first glove remover

3D printed by 3dprintingbykevin.com, and we are here prepared to battle COVID-19. 

Get yours today from 3dprintingbykevin.com.

contact@3dprintingbykevin.com

The most effective method to use the glove remover

1. Turn the palm of your hand towards the device without contacting it.

2. Point the tip of the glove remover against your wrist. Then slide the tongue into the glove between the palm of your hand and the glove sleeve.

3. Draw your hand upwards; the glove will roll right off and drop into the waste bucket. Would you please take caution to never contact the glove remover with the outside of your glove?

Note: If your glove does contact the glove remover, please disinfect it and whatever else touched it immediately.

Instructions to Mount the 3D Printed Glove Remover

Install the glove remover and position the tip at 60 and 80 cm (24 and 31 inches) over the floor. Put a low-profile waste container underneath.

Wall mounting:

Install the wall mounting plate (two teeth) with two screws vertically, one over the other on an appropriate divider.

Supplement the glove remover into the wall mounting plate and screw it on. Use two screws for plastics on each side.

Pipe mounting:

Use a measurement of 2.5 cm (1 inch). For littler channels, wrap tape over a width of 6 cm (2.5 inches) around the round tube or pipe until a sufficient diameter is reached. 

Cinch the glove remover to the pipe using the channel mounting plate (4 round countersunk holes). Use four screws specifically for plastics and screw them into the mounting plate from behind.

3D Printed Glove Remover Health Information

The glove remover works best with generally used gloves made of nitrile rubber, which are not tight-fitting or have a low cuff.

 People shouldn’t use the glove remover to pull off surgical, chemotherapy, and other tight-fitting gloves with a high sleeve since they are bound to tear.

The potential of contamination of the skin, clothing, and glove remover can happen if the glove tears. Yet, it is your job as the user to conduct yourself carefully. The glove remover ought to be disinfected consistently.

We hope you found this article helpful. If you did, please let us know by leaving a comment or question on the website. Also, if you know someone who might benefit from this information, please share it.

3d Printed glove remover

Thanks for being part of the community!

Kevin

contact@3dprintingbykevin.com

Disclaimer: 3d printing by Kevin disclaims all liability for damage to people or property connected with the production or use of the glove remover.

Grammarly proofread this post.

Please leave them in the comments below if you have any additional questions.

As an eCommerce seller, the first physical touchpoint you’ll have with a customer is when your package arrives at their door, an impactful impression is critical.

Fulfillment marketing, a cutting-edge solution crafted by my friends over at The Fulfillment Lab, is designed to make the unboxing experience memorable by bringing marketing and fulfillment together at scale!

With this strategy, you can create a unique order fulfillment experience using data you’re already capturing—without sacrificing speed or scalability. It makes it possible to:

  • Build brand recognition. With increasing competition for eCommerce businesses, you need a way to differentiate and build brand recognition. Fulfillment marketing is that solution!
  • Tailor the customer experience. Personalize the fulfillment experience to each buyer using marketing data you’re already collecting—delivering a unique customer experience that’ll leave a lasting impression.
  • Create brand advocates. Turn one-time buyers into repeat buyers and loyal advocates for your brand. You make it easier to attract new customers driving additional revenue from repeat sales while expanding your new customer base.

I figured you’d like to do this in your organization, so I’m connecting you with The Fulfillment Lab! Click this link [HERE] to get started with their fulfillment services today, or contact them directly if you have more questions.

The Fulfillment Lab, 5136 W Clifton St, Tampa, FL 33634, (813) 444-3455

Unsubscribe Manage preferences